Radix DMC-4000T Betriebsanleitung Seite 77
- Seite / 331
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
6 Communication settings and guide of HMI connecting with controller
4715H Alarm 1 type
Please refer to the contents of the “Alarm Outputs” for detail.
In the setting mode
4716H Alarm 2 type
Please refer to the contents of the “Alarm Outputs” for detail.
In the setting mode
4717H
Temperature unit display
selection
o
C : 1 (default),
o
F : 0. in the setting mode
4718H
Heating/Cooling control
Selection
Heating: 0 (default), Cooling: 1. in the setting mode
4719H Control Run/Stop setting
Run: 1 (default), Stop: 0. in the running mode
471AH
Communication write-in
selection
Communication write in disabled: 0 (default),
Communication write in enabled: 1.
In the setting mode
471BH Software Version V1.00 indicates 0 x 100
4729H AT Setting
OFF: 0 (default), ON: 1. in the adjusting mode
4733H CT monitor value
Unit is 0.1A. in the running mode
DTB9696VR：Address and Content of Word Register (corresponds to 4X in the HMI)
Address Content Explanation
1000H Process value (PV) Measuring unit is 0.1, updated one time in 0.4 second
1001H Set point (SV) Unit is 0.1,
o
C or
o
F
1002H Upper-limit of temperature range
The data content should not be higher than the
temperature range. In the setting mode
1003H Lower-limit of temperature range
The data content should not be lower than the
temperature range. In the setting mode
1004H Input temperature sensor type
Please refer to the contents of the “Temperature Sensor
Type and Temperature Range” for detail. In the setting
mode
1005H Control method
0: PID, 1: ON/OFF, 2: manual tuning, 3: PID grogram
control. In the setting mode
1006H Heating/Cooling control selection
0: Heating, 1: Cooling, 2: Heating/Cooling, 3:
Cooling/Heating. In the setting mode
- 74 -
- CONTENTS 1
- Printer 26 pin port 6
- Note：the red line is 6
- 14 Autofeeddxt 11
- 4 Download Cable Diagram 13
- RJ45 RJ45 14
- 5 Refresh Kernel and Rootfs 15
- 5 Refresh kernel and rootfs 16
- 6.2 Allen-Bradley 21
- Serial System Communication 22
- SLC500 RS232 communication 24
- RSLogix500 software setting 24
- RSLogix5000 software setting 25
- SLC 5/03 RS232 cable diagram 32
- PLC-5 RS232 cable diagram 32
- 9 pin D-SUB (male) 35
- 6.5 AysjNet 38
- Baldor NextMove ES 39
- 6.7 Barcode 42
- Baumuller 43
- RS485-4 communication cable 44
- 6.10 Bosch Rexroth 45
- PLC Software Settings 47
- L40 software setting 49
- 6.11 Bosch Rexroth Ethernet 54
- 6.12 CANOpen Node Slave 58
- Parameters Setting 59
- 6.13 Danfoss Inverter 66
- Inverter setting 67
- of process word: 68
- Modbus RTU Protocol: 69
- 6.14 Delta Corporation 72
- Controller Setting 75
- Project configuration 84
- 6.17 ENDA 86
- 6.18 Emerson NetWork Power 88
- 6.19 Epower 92
- 6.21 Facon Corporation 96
- 6.22 Fuji SPB 99
- System configuration 100
- Communication Setting 100
- Supported Device 100
- Cable Diagram 101
- Serial Communication 102
- Network communication 103
- Serial System configuration 104
- Network System configuration 104
- Serial Communication Setting 105
- HMI terminal 110
- 9pin D-SUB female/male 110
- CMM311 port2 terminal 110
- 25 pin D-SUB (male) 110
- 6.24 HAIWELL 111
- 6.26 Hitachi Inverter 114
- 6.27 Hitachi IES Co., Ltd 116
- 网口通讯参数设置 122
- 6.29 HuaDA HD-JZ06 125
- PLC setting 129
- MODBUS-RTU Slave protocol 130
- 6.33 Kinco Corporation 133
- 6.34 Kinco Servo Series 135
- RS485 communication cable 138
- Keyence KV-16DT 138
- Keyence KV-1000 138
- Keyence KV-3000 138
- PLC configuration 140
- KV-1000 142
- KV-3000 142
- KV-5000 143
- Koyo Direct 145
- 6.37 KTC Srdlink 148
- 6.38 KYL Slave 150
- RS232 communication 155
- RS485 communication 155
- LG Modbus Rtu communication 156
- RS232 communication cable 163
- RS485 communication 174
- RS422 communication 174
- MemoryMap(Master-Slave) 175
- 6.44 Millenium3 176
- Network Communication 179
- (support multi station) 184
- PLC Software Setting： 185
- 6.46 Mks controller 200
- 6.47 ModBus 202
- 6.48 MODROL 209
- 6.49 OE MAX 210
- 6.50 Omron Corporation 212
- Network configuration 219
- 6.54 PMAC Motion Controller 234
- Controller terminal 236
- 9pin D-SUB(male) 236
- 6.56 Profibus Slave 238
- 6.57 RF-IC (Card Reader) 242
- 6.58 RKC Instrument INC 243
- 6.59 SAE J1939 246
- Systems Configuration 246
- 6.60 Saia-Burgess 248
- PLC Setting 255
- 6.63 SHIMADEN FP23 261
- 6.64 SIEMENS 263
- 6.65 TAIAN 285
- Controller 287
- RS485 terminal 287
- RS232 Communication Cable 289
- 6.68 Toledo DLoadCell 291
- 9pin D-SUB female\male 292
- RS422 terminal 292
- Controller internal setting: 294
- RS485-4 communication 294
- 6.70 Unitronics 296
- 6.71 Universal ASCII Slave 301
- 6.72 Vigor Corporation 302
- 6.73 XiLin Inverter 304
- 6.74 Yamatake Corporation 306
- Yaskawa MP2300 311
- Yaskawa SGDM 311
- Inverter 311
- PLC software setting 314
- HMI Ethernet terminal 319
- Ethernet Hub or Switch 319
- 6.77 YuDian AI 327
- AI-701 329
- AI-7048 330
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.108 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern